ACTi E41A Guide d'installation

2013/12/06 Bullet with Bundled Removable Bracket Mounting on a Corner using the Accessory Set Installation Guide For Models: D3x

www.acti.comInstallation Guide 10 Installation Using the Corner Mount with Bracket and Flex Conduit The D4x, E3x, E41, E41A, E42, E42A, E43, E43A

www.acti.comInstallation Guide 11 Step 1: Install the Corner Mount 1. Align the Corner Mount to the corner wall and mark the location of the eigh

www.acti.comInstallation Guide 12 Step 2: Install the Bracket 1. Remove the screw to detach the camera holder from the bracket. Set the holder as

www.acti.comInstallation Guide 13 Step 3: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to detach the back co

www.acti.comInstallation Guide 14 Step 4: Prepare the Conduit Gland and Flex Conduit 1. Disassemble the bundled conduit gland as shown below.

www.acti.comInstallation Guide 15 4. Insert the clamping nut through the flex conduit. 5. Insert the sealing insert and attach it at the end o

www.acti.comInstallation Guide 16 2. Secure the clamping nut to the body. NOTE: Make sure the clamping nut is tight to avoid possible water le

www.acti.comInstallation Guide 17 Step 7: Install the Camera 1. Align the screw holes of the holder to the bottom screw holes of the camera. 2.

www.acti.comInstallation Guide 18 4. Loosely attach the screw to secure the holder to the bracket. 5. As needed, turn the holder left or right

www.acti.comInstallation Guide 19 Step 8: Connect the Camera to the Network Connect the other end of the Ethernet cable to a PoE switch. Step 9:

www.acti.comInstallation Guide 2 Table of Contents Installation Procedures ... 4 Installation Us

www.acti.comInstallation Guide 20 Installation Using the Corner Mount with Bracket and Naked Cable The pre-installed network cable comes with an E

www.acti.comInstallation Guide 21 Step 1: Install the Corner Mount 1. Align the Corner Mount to the corner wall and mark the location of the eigh

www.acti.comInstallation Guide 22 Step 2: Install the Bracket 1. Remove the screw to detach the camera holder from the bracket. Set the holder as

www.acti.comInstallation Guide 23 Step 3: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to detach the back co

www.acti.comInstallation Guide 24 Step 4: Install the New Ethernet Cable 1. Insert the new Ethernet cable through the sealing nut, claw, seal, a

www.acti.comInstallation Guide 25 4. Tighten the sealing nut. NOTE: Make sure the rubber seal is tightly squeezed to avoid possible water le

www.acti.comInstallation Guide 26 2. Attach the two (2) screws (supplied in the heavy duty bracket package) to secure the camera to the holder.

www.acti.comInstallation Guide 27 5. As needed, turn the holder left or right to adjust the camera viewing direction. Then, secure the screw tigh

www.acti.comInstallation Guide 28 Appendices How to Access the Camera Live View Connect the Equipment To be able to connect to the camera firmwar

www.acti.comInstallation Guide 29 The quickest way to discover the cameras in the network is to use the simplest network search, built in t

www.acti.comInstallation Guide 3 How to Make an Ethernet Cable ... 40 Safety Informati

www.acti.comInstallation Guide 30 If you work with our cameras regularly, then there is even a better way to discover the cameras

www.acti.comInstallation Guide 31 Use the default camera IP address: If there is no DHCP server in the given network, the user may have to assign

www.acti.comInstallation Guide 32 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same loc

www.acti.comInstallation Guide 33 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the sam

www.acti.comInstallation Guide 34 The following examples in this manual are based on Internet Explorer browser in order to cover all functions of

www.acti.comInstallation Guide 35 To check the firmware version through the Web Configurator, access the Setup page and click System > System I

www.acti.comInstallation Guide 36 How to Adjust Focus This section describes the procedures in adjusting the viewing angle and focus of the differ

www.acti.comInstallation Guide 37 3. Attach the lens focus tuner to the lens. D3x Series E3x Series 4. Adjust

www.acti.comInstallation Guide 38 D4x / E41 / E41A / E42 / E42A / E43 / E43A Series 1. Open the front cover. 2. Based on the live view fro

www.acti.comInstallation Guide 39 How to Attach the Sunshield The use of sunshield is optional if the camera will be installed indoors. However, i

www.acti.comInstallation Guide 4 Installation Procedures The camera can be installed onto a corner using additional mounting accessories. The acce

www.acti.comInstallation Guide 40 How to Make an Ethernet Cable 1. Prepare the following tools:  Ethernet cable without connectors  RJ-45 Con

www.acti.comInstallation Guide 41 Safety Information Read these instructions You should read all the safety and operating instructions before usin

www.acti.comInstallation Guide 42 Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to

www.acti.comInstallation Guide 5 Installation Using the Corner Mount with Bracket and Sealant Tape Step 1: Install the Corner Mount 1. Align th

www.acti.comInstallation Guide 6 Step 2: Install the Bracket 1. Remove the screw to detach the camera holder from the bracket. Set the holder asi

www.acti.comInstallation Guide 7 Step 3: Install the Camera 1. Align the screw holes of the holder to the bottom screw holes of the camera. 2.

www.acti.comInstallation Guide 8 4. Loosely attach the screw to secure the holder to the bracket. 5. As needed, turn the holder left or right t

www.acti.comInstallation Guide 9 Step 4: Connect the Cables 1. Connect the Ethernet cable from the network side to the Ethernet port of the camer